"f" 0.25 [.100] designed & dimensioned in millimeters[inches] do not scale from this print 3.81 .150 "e" 2.88 .113 ref 0.30 ref .012 2.00 - 0.20 +0.25 .079 - .008 +.010 c uppt-xx-ra-sd sub-c-263-xx-x sub-t-1m70-xx-x "a' ref "b" ref "c" ref 0.37 .015 ref 3.18 .125 ref (2 plcs) "d" ref 5.62 .221 ref 8.42 .332 ref 'a' 01 n 1.54 - 0.38 +0.13 .061 - .015 +.005 "h" 0.25[.100] 4.10 ref .161 6.50 .256 ref 1.50 .059 c c fig. 1 (uppt-08-01-01-x-ra-sd shown) c c c plating specification -l: (see table 3) -t: (see table 3) -sd: screw down -lc: locking clip option packaging -tr: tape & reel (see note 7) tail length -01: for 1.57[.062] thick pcb (use sub-t-1m70-01-x and sub-c-263-01-x) -02: for 2.36[.093] thick pcb (use sub-t-1m70-02-x and sub-c263-02-x) right angle -01 lead style -02, -04, -06, -08 no of positions uppt-xx-01-xx-x-ra-xx-xx "f" 0.25 [.100] sheet of unless otherwise specified, dimensions are in millimeters. tolerances are: decimals angles x.x: 0.3 [.01] 2 x.xx: 0.13 [.005] x.xxx: 0.051 [.0020] material: micro power hermi connector by: uppt-xx-01-xx-x-ra-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b harpenau 09/11/2009 2 1 sheet scale: 2:1 insulator: lcp contact and terminal: becu f:\dwg\misc\mktg\uppt-xx-01-xx-x-ra-xx-xx-mkt.slddrw max flash allowed: 0.08[.003] max gate vestige: 0.08[.003] notes: 1. represents a critical dimension. 2. burr allowance: 0.038[.0015] max. 3. minimum pushout force: 4.45n[1.000 lb]. 4. maximum allowable bow: 0.05[.002] mm/mm after assembly. 5. position 1 will mate to position n on mating connector. 6. recommended torque on hold down screws to be 20 in-oz 5 in-oz. 7. parts to be packaged in tubes unless otherwise stated. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision b
2.09 0.00 +0.13 .082 - .000 +.005 1.69 .067 detail 'a' scale 4 : 1 c c "g" lc-06-tm fig. 2 (uppt-08-01-01-x-ra-lc shown) uppt-xx-ra-lc 1.40 .055 c 21.49 .846 (uppt-02-01-01-x-ra-sd shown) fig. 3 user direction of un-reeling pocket not detailed packaging view -tr option packaging tube view b b b sheet of micro power hermi connector by: uppt-xx-01-xx-x-ra-xx-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing b harpenau 09/11/2009 2 2 sheet scale: 2:1 revision b f:\dwg\misc\mktg\uppt-xx-01-xx-x-ra-xx-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
